Randomization in DM Brush
6 posts
• Page 1 of 1
Randomization in DM BrushIt would be useful to have a randomization feature with a range setting in the DM Brush in addition to relative and absolute.
Hi Nicethugbert,
Thanks for the suggestion. Do you want randomisation of all DM parameters (except climate & spec. type/params), or just altitude? [bearing in mind that random altitude variation is already supported using the peak noise parameter] Cheers, Aaron.
The problem I have in mind is where I want to have two different terrains on a map, like a border region, but, the map is too small for L3DT to give me that. I have to go with the smaller map, and other parameters for the sake of satisfying NWN2 limitations, game play, etc.
So, I set L3DT to get me a nice map in terms of other criteria. Then I go to the design map and brush into specific sections settings that are known to give me the desired terrain. But, the regions are all uniform now instead of having the variations it would have had if L3DT had done it. So, If I can brush in randomization then I expect it'll look "normal". Arid vs. humid and plateau vs. depression on the same map are examples of what I want to achieve. Let's say I have two bowl shaped depressions separated by a line of ellevation and I want to raise one bowl higher that the other. I want the lower bowl to be desert and the upper bowl not desert. What would I do without having to handle this one DM square at a time? Such things exist in nature but on a scale much more vast than is feasible in a game. But, the players will be highly unlikely to know or care that the two regions change too drastically is the space of a kilometer or three. Even if I simulated four different levels of moisture in 400 meter increments it would be realistic to the vast majority of players but not actually realistic at all. Or, maybe there are scaling tricks I can use? If increase the horizontal scaling to get more terrain types in one map, I lose the needed height. EDIT 0: Just wanted to add that I'm working in 240 meter increments with a 160 meter border. At 1120x1120 meters I'm getting ~420 meter altitude difference with max avg. alt., max steepness, and max vast and the map imparts a sense of vastness. With a 1600x1600 meter map, you may as well say you are in the Himalayas. EDIT 1: Hmm, I could just use 50% Erosion, Cliffs, and Lakes. Then I could brush on relative changes of those over a region to get my humidity setting. That still leaves the bowl depth and height problem.
Hi nicethugbert,
Can you please post a screenshot of the heightfield in 3D? I've designed plenty of terrain by hand, from a blank design map, and I don't find L3DT producing bland uniform terrain, unless I deliberately make it so. Did you remember to set the peak and fractal noise channels on the design map? How about erosion and cliffs / terracing?
Climate variation within the map? This has to be painted by hand using the design map brush. It's not the sort of thing that should be automated, in my opinion. Too much variation in user expectation.
That's the terracing / cliffs channel, again. It may also help to set a small relative altitude value in the design map brush to raise up your plateau (if positive) and lower your depression (if negative). This is how I built the fjord terrain from a completely blank design map.
Increase the brush radius?
Don't use design map 'lakes' unless you really mean it. Does your game engine support multiple water bodies at different heights? Few do. Cheerio, Aaron.
I misspoke. I have not made such maps because my attempts at brushing are horrible failures. Also, I failed to mention that when I envision raising a depression, I also want to make it shallower.
But, I see now that to make depressions shallower while maintaining the height of the rim I'll have to set a brush to a narrow radius and a relative height increase. Then keep expanding the radius but maintain the same brush epicenter. But that assumes the depression is round. When I said I could just use 50% Erosion, Cliffs, and Lakes I was thinking of the design map parameters. I would use them as a base line then brush relative values to get arid and non-arid areas on the same map. I'll add that I use extremely low values of Noise Strength and Noise Shape because the path finding algorithm in NWN2 gets confused and slows down easily. I'll go down as low as like 8% and 0% respectively. A quick question, which parameters are related to height? I fear that if I mess with heights then I am contradicting L3DT's algorithms.
Hi nicethugbert,
No, please feel free to mess with heights. L3DT won't get upset*. Cheerio, Aaron. * Exception: when using the 'Operations->Design map->Modify parameters' option, you will not be allowed to change the average altitude, altitude range or feature scale. You can however change the height values using the brush tools at any time.
6 posts
• Page 1 of 1
Who is onlineUsers browsing this forum: No registered users and 23 guests |